Simonton Sliding & Patio Doors Nationwide | TruePane Windows & Doors

Simonton Sliding & Patio Doors: The Davie Owner’s Guide

If your Simonton sliding or patio door is sticking, dragging, or letting daylight through where it shouldn’t, we stock and install Simonton-compatible rollers, tracks, handles, locks, weatherstripping, and replacement panels for most Simonton models. In Davie, a typical Simonton sliding door roller and track replacement runs $165 to $340 installed, and our technicians carry the most common Simonton parts on the truck so most jobs are finished in one visit.

Call (863) 208-5172

Most Davie homeowners discover a failing part the hard way: the door grinds across the track one morning, a screen jumps its rails, or the handle won’t latch after a hard summer of daily use. South Florida humidity and salt air are rough on sliding door hardware. Rollers corrode. Tracks pit. Vinyl weatherstripping dries out and cracks in the heat. The good news is these are wear items, not a sign you need a whole new door.

Which Simonton Models This Applies To

We work on the full range of Simonton sliding and patio door lines you’re likely to find in Davie homes: the Simonton Reflections series, the StormBreaker Plus impact-rated line, the Madeira and Vinyl Master series, and the older ProFinish models that were discontinued but still sit in hundreds of Broward County houses. Each series has its own roller assembly dimensions and track profile, and mixing them up means a door that binds within six months.

Before you call, check the corner of the glass panel or the door’s edge frame for a Simonton label. It usually has a model number and manufacture date etched or printed. If you can’t find it, measure the roller wheel diameter and the width of the track channel. We can match almost anything from those two numbers plus a photo. Simonton’s OEM parts are solid, but for rollers specifically, we often recommend a quality aftermarket stainless-steel replacement that holds up longer in coastal air than the factory nylon wheels did. On glass panels, though, stick with Simonton’s own glass packs if you want your warranty intact.

One compatibility gotcha we see often in Davie: a StormBreaker Plus impact door shares its general frame design with the Reflections line, but the interlocking rail and weatherstripping are different, and installing the wrong interlock makes the door impossible to seal tight. If you are not sure which line you have, a photo of the door from three feet back usually tells us what we need to know.

Signs Your Simonton Sliding & Patio Doors Is Failing

• The door is hard to slide, even after cleaning the track. Rollers wear flat, or their bearings seize from corrosion. You’re dragging glass and aluminum across a track that was never meant to carry that much friction.
• The door lifts up or drops when you pull the handle. This points to a broken roller housing or a bent adjustment screw. Left alone, the panel sags and the door starts chewing into its own track.
• The handle turns but the latch doesn’t move. Inside the handle assembly is a small gear and a cam bar. South Florida humidity eats the internals of Simonton handles faster than you’d think, especially on west-facing doors in Davie that bake all afternoon.
• You can see daylight or feel a draft at the interlock. The weatherstripping at the meeting rail has compressed or torn. This is also the number one way water sneaks in during a summer thunderstorm.
• The door glides too easily, and then slams into the frame. The roller adjustment is maxed out or the roller has come off its track entirely. That slam, repeated, is how lock stiles crack in older Simonton vinyl frames.

Replacement Cost & What’s Included

In Davie, figure on these installed ranges for Simonton sliding door work:

• Roller replacement (both panels): $165 - $290
• Track replacement or repair: $120 - $220
• Handle and latch assembly: $110 - $185
• Weatherstripping and interlock seal (full door): $95 - $160
• Screen replacement (rolling screen): $140 - $260

What drives the range is your specific Simonton series and whether the track needs shimming or the panel requires realignment after the swap. Every quote is line-itemed on paper before work starts: the part, the labor, and any adjustment time. You’ll see it all. Our workmanship is covered by the Done Right Promise, and The Keystone Standard means we register both manufacturer warranty layers in writing before our truck leaves your driveway. No fine print, no arguing.

DIY or Call Us?

Here’s the honest split. You can safely check a few things yourself: clean crud out of the track with a stiff brush and a vacuum, tighten a loose handle screw with a screwdriver, check whether the door only drags in the winter when the frame contracts. Those are inspections, not repairs. What we recommend against is pulling a Simonton sliding door panel out of its frame without help. These panels are heavier than they look, the tempered glass can’t take a sharp hit at the corner, and a panel that comes off its rollers at the wrong angle is how fingers get pinched and tile gets cracked. If the door itself is coming off the track or the rollers are shot, that is a job for a technician with the right tools. Call (863) 208-5172 and we’ll come measure, match the part, and fix it in one visit.

FAQs