Free in-home measure and quote - PGT, CGI and CWS impact lines compared on your actual openings, style by style
Sliding glass doors
Impact garage doorsPGTCGI
Before
After
Before
After
Before
AfterCWS Door Installation: The Davie Owner’s Guide
We stock and install CWS door parts across Davie, with most replacements running $220 to $480 installed depending on the component and finish. The work is usually completed in a single visit, and we keep the most common CWS components on the truck so we’re not scheduling a second appointment while your door sits out of square. Most Davie homeowners discover the failure the same way: a door that suddenly drags against the frame in the afternoon heat, a roller that groans, or a handle that stops catching. It starts as a nuisance, but in Broward County humidity and rain, a door that won’t latch or seal is costing you cooling dollars and inviting water into the threshold.
Which CWS Models This Applies To
CWS built sliding patio doors and hinged entry doors in several series lines over the years, and the parts are not interchangeable the way some folks assume. The most common CWS doors we see in Davie homes are the aluminum slider series, which take a narrow-profile roller assembly, and the swing-door line, which uses a multi-point lock set that differs from the single-bolt hardware on older models. The fastest way to identify what you have is the manufacturer label on the door’s edge, usually printed on a small white or silver sticker near the hinge or the top track. If that label has worn off, measure the roller’s wheel diameter and housing width, or photograph the lock’s faceplate. One gotcha we run into regularly: CWS used two different roller housing heights within the same series run, and forcing the wrong size is how doors end up binding worse than before. We match off the physical part and the door’s series number, not guesswork.
On the OEM versus aftermarket question, we are direct about the tradeoff. CWS original parts are the safest fit for warranty-sensitive or odd-size units, and for some lock sets they are the only route. For rollers and handles, quality aftermarket equivalents from established hardware manufacturers often outlast the originals, especially the nylon-wheel roller upgrades we recommend for homes within a few miles of the coast. We are an independent service provider, not affiliated with CWS, so our recommendation is based on what holds up in Davie’s heat and salt air, not on a company catalog. We also stock and service parts for Andersen, and Pella doors, which matters when a Davie home has mixed brands across different openings.
Signs Your CWS Door Installation Is Failing
- Door drags or sticks along the track or threshold. On sliders, the roller bearings flatten over time and the wheel can develop a flat spot. On hinged doors, the hinges sag slightly and the door’s weight falls out of plane. Both get worse as the aluminum frame expands and contracts through a Davie summer.
- Handle or lock requires a shove to latch. The multi-point lock’s gearbox or connecting rods wear just enough that the latch points are no longer aligned with the keepers. Forcing the handle eventually rounds out the gear and leaves you locked out or, worse, locked in.
- Water or daylight visible at the bottom corner. The sweep and threshold gasket flatten with heat and use, and once the seal goes, a south-facing Davie door makes the room warmer within a week. If you can see light under the door with it closed, the gasket is already gone.
- Rollers grind, squeal, or the door shudders when moved. The original CWS rollers often had steel bearings that corrode in coastal humidity. Once corrosion starts, the wheel stops spinning and the door gets dragged across the track, which scores the aluminum.
- Frame corners or the sill feel soft underfoot. A failing door installation will sometimes show itself in the frame before the part itself breaks. Moisture that gets past a worn threshold eats at the subfloor in older Davie homes, and softness under the sill means the problem has been going on longer than most people assume.
Replacement Cost & What’s Included
Installed CWS door part replacement in Davie runs $220 to $480 for rollers, handles, lock sets, or threshold components on most models. A basic roller swap with quality aftermarket wheels runs at the lower end. A full multi-point lock replacement with OEM CWS hardware lands at the higher end. The spread comes down to one thing: whether we are replacing one worn component or the full assembly, and whether your door needs an OEM-only part. Every quote is a fixed line-item number. You’ll see the part cost, the labor, and the warranty terms on paper before we start. There are no change orders tucked into the bill. Junkyard-adjacent pricing is not our lane. The work is done right, both manufacturer warranty layers get registered in writing, and our Done Right Promise covers the labor. If something’s off after the install, we return and fix it. No paperwork fight, no arguing.
DIY or Call Us?
A homeowner can safely check a few things: whether the screws in the handle and hinge plates are snug, whether the track is clear of grit and pet hair, whether the weep holes at the bottom of the frame are clean and draining. What we do not recommend is wrestling with a multi-point lock assembly or pulling a slider panel off its track. A double-panel CWS slider weighs well over a hundred pounds, and the lock’s gearbox is under spring tension in some models. The wrong move with a flathead screwdriver can send a gear or clip into the frame cavity, and the repair bill climbs from there. The inner workings of a CWS door are not buried complexity, but they are precise. If the door is not rolling or latching right, call (863) 208-5172. We will check the part, match it, and set it square the first visit.
FAQs
Original CWS rollers in a Davie home typically last 7 to 12 years, and about half that close to the coast or on a west-facing door that takes direct afternoon sun. The nylon-wheel replacements we install generally outlast the original steel-bearing rollers because the wheel material does not corrode in salt-heavy air. Call (863) 208-5172 for an exact assessment and a fixed quote.
A specific part, like a lock cylinder or a single roller housing, can sometimes be serviced rather than swapped, but assembled components like a multi-point gearbox or a flattened roller usually need full replacement. We don’t rebuild a worn gearbox because it fails again and the second call costs more than one proper fix. The call to us is free, and the estimate is in writing before any work starts.
Most single-part CWS door repairs take under two hours from truck arrival to cleanup. A full multi-point lock replacement with a new handle set can take three to four hours. The work is finished the same visit; we don’t leave a job half-done. Call (863) 208-5172 to schedule and we will give you a straight arrival window.
We keep the most common CWS roller assemblies, lock sets, handles, thresholds, and sweeps stocked on the truck, so most Davie jobs are done in a single visit. For an older or odd-size CWS unit, we source the exact part, show you the line item, and return to install it once it arrives. Call (863) 208-5172 and we’ll tell you whether your door’s part is already on hand.
Contact
If your CWS door is binding, dragging, or not latching, we’ll match the right part and set the frame square. We are second-generation glaziers, not a franchise playbook. Dale Kessler grew up here, trained at McFatter Technical College in Davie, and has been setting doors in Broward County for twenty-six years. The whiteboard in our shop has one rule on it: if the pane is not true, the job is not done. He applies that to every door, every seal, every threshold. Call (863) 208-5172 for a free estimate. We answer the phone.
Written by Dale Kessler, Owner, TruePane Windows & Doors at TruePane Windows & Doors, serving Davie and nearby areas.
Six Reasons Homeowners Choose TruePane Windows & Doors
Impact systems engineered to design pressures up to +/-100, matched to your wind zone - your openings hold when the storm arrives.
Low-E insulated impact glass from our manufacturer lines commonly cuts monthly cooling bills 20-30%.
Laminated impact glass shuts out up to 40% of outside noise - traffic, neighbors, weather.
Monitoring services run $30-90 a month. Laminated impact glass resists forced entry around the clock, with no subscription.
Florida homeowners average around 25% savings on the windstorm portion of their policy after protecting every opening - some homes qualify for more.
A full impact package upgrades curb appeal, buyer confidence and appraised value in one project.