Last updated August 27, 2026
Free in-home measure and quote - PGT, CGI and CWS impact lines compared on your actual openings, style by style
The Complete Guide to Windows & Doors in Davie
Most homeowners in Davie don’t think about their windows and doors until something goes wrong. Then they discover that South Florida has its own set of rules: hurricane codes, humidity that warps wood, and salt air that corrodes hardware faster than anywhere else in the continental United States. This guide covers what actually matters when you’re buying, replacing, or maintaining windows and doors in Davie: the code requirements, the material tradeoffs, the pricing realities, and the installation details that determine whether you get twenty years out of a window or five.
Quick Answer
Windows and doors in Davie need to meet Florida Building Code impact standards for wind and debris, handle year-round humidity and salt air, and be installed square and sealed correctly or they’ll fail early. Most homeowners should budget $600 to $1,400 per window installed and $1,800 to $5,000 per exterior door, depending on material, impact rating, and size. The single most important decision is not the brand name on the glass; it’s the quality of the installation and whether both warranty layers are registered in writing.
Table of Contents
- Davie Building Code and Impact Requirements
- Window Materials That Hold Up in South Florida
- Choosing Exterior Doors for Davie’s Climate
- What Windows Cost in Davie
- What Doors Cost in Davie
- Why Installation Quality Determines Everything
- Energy Efficiency and Your Electric Bill
- Maintenance That Extends the Life of Your Investment
Davie Building Code and Impact Requirements
Davie sits in Broward County, which means every window and exterior door installed in a residential structure must meet the High Velocity Hurricane Zone requirements of the Florida Building Code. This is not optional, and it’s not a suggestion. If you’re replacing windows in an existing home, the new units need to be either impact-resistant (laminated glass tested to withstand a 9-pound 2×4 fired at 34 miles per hour) or protected by an approved shutter system.
Why this matters in practice: an impact-rated window is not just thicker glass. It’s a laminated assembly with an interlayer, usually polyvinyl butyral, that holds the glass together when it shatters. That interlayer is what keeps wind and rain out of your home during a storm when a window takes a direct hit from a palm frond or a piece of roof tile. In Davie, where the tree canopy is dense and hurricanes are a question of when rather than if, this is the difference between a broken window and a destroyed living room.
Here’s what you need to know before you buy:
- Product Approval matters. Every window and door installed in Davie must carry a Florida Product Approval number, sometimes called an FL number. Our technicians confirm this number with the manufacturer on every quote so the permit inspection goes through without a problem.
- Not all impact glass is the same. There are three common ratings: Small Missile (for windows and doors on upper floors), Large Missile (required for anything within 30 feet of grade, which covers most residential windows in Davie), and Pressure-and-Impact. Your specific opening and exposure determines which rating applies.
- Permits are required. Window and door replacement in Davie requires a permit, and the installation must pass an inspection. Anyone who tells you otherwise is not doing the job legally.
- Older homes often have grandfathered openings. If your home was built before the current code cycle and never replaced its windows, you’re not required to upgrade unless you’re replacing the units. But the moment you do replace them, the new windows must comply with current code.
The brands we quote most often for impact-rated work in Davie are PGT, CGI, and ES Windows. PGT’s WinGuard series is common in the area and does well in the Large Missile category. CGI makes a solid impact window with cleaner sightlines than most competitors. ES Windows is a newer line that has gained ground in Broward County for its European-quality laminated glass and frame construction. Each has different lead times and price points, and we’ll show them side by side on paper so you can see exactly what you’re paying for.
Window Materials That Hold Up in South Florida
This is where homeowners in Davie get burned most often. A window frame that works perfectly in Minnesota will warp, rot, or corrode within a few years of South Florida exposure. Here’s a straight assessment of the four main frame materials, based on what we’ve repaired and replaced in Davie homes over the years.
Vinyl
Vinyl is the most common replacement window in Davie because it’s affordable and holds up well in humidity. It won’t rot or rust, and modern vinyl extrusions from Simonton and Ply Gem are engineered with internal chambers that improve structural rigidity and insulation. The weakness is heat. Vinyl expands and contracts more than other materials in direct sun, which can eventually cause seal failures at the corners. A quality vinyl window is a practical, budget-conscious choice for most homes in Davie. A cheap vinyl window, the kind with thin walls and flimsy reinforcement, will start bowing within five years and you’ll feel the gaps.
Aluminum
Aluminum was the standard in South Florida for decades. It’s strong, slender, and handles high winds well, which is why it’s still common in high-rise and mid-rise buildings. The issue in Davie is condensation and corrosion. Aluminum conducts heat readily, and when warm, humid outside air meets air-conditioned interior air, moisture forms on the frame. Over time, that moisture eats at the metal, especially near salt-adjacent air along the coast, not far from Davie. Modern thermally broken aluminum frames address part of this, but they add cost and complexity. We typically recommend aluminum only when the existing openings require it or when a homeowner specifically wants narrow sightlines.
Fiberglass
Fiberglass is the best-performing frame material for Davie’s climate, and it costs accordingly. It expands and contracts at nearly the same rate as glass, which means seals are less likely to fail over time. It’s impervious to humidity, doesn’t rot or warp, and can be painted. For homeowners planning to stay in their home another twenty years, fiberglass, whether from Andersen or Marvin, is often the smartest long-term purchase despite the higher upfront price.
Wood and Wood-Clad
Wood windows from Andersen and Pella have a place in Davie, mostly on the interior side where homeowners want the look of real wood. The problem is exterior exposure. Even with aluminum cladding, the wood core eventually sees moisture in South Florida’s humidity, and wood rot is one of the most expensive repairs you’ll face. If you choose wood windows in Davie, you need to be disciplined about maintenance: checking glazing beads, keeping drains clear, and repainting or refinishing on schedule. For most homes, we recommend a fiberglass or high-quality vinyl exterior with wood-look interiors.
Choosing Exterior Doors for Davie’s Climate
Exterior doors in Davie face the same enemies as windows, with the added complication of daily use. A front door gets opened and closed thousands of times a year, and South Florida humidity means the door swells, the frame shifts, and hardware takes abuse.
Fiberglass Doors
For Davie, fiberglass entry doors are the best all-around choice. They don’t warp, they don’t rot, they hold paint well, and they’re available with wood-grain textures that look like natural oak or mahogany from three feet away. They also offer solid insulation values. Most fiberglass doors are engineered with a polyurethane foam core, which keeps your air conditioning inside and the summertime heat outside.
Steel Doors
Steel entry doors are strong and secure, which appeals to many Davie homeowners. The drawback is rust. In Davie’s humidity, steel doors need regular maintenance: chips in the paint exposed to moisture will start rusting within months, not years. If you choose steel, plan on inspection and touch-up at least once a year, especially near the bottom rail where water tends to pool.
Wood Doors
A solid wood door is a beautiful thing, and plenty of Davie homes have them. They also require the most upkeep. In July and August, when the dew point sits in the mid-70s for weeks on end, wood doors expand. If the door was hung tight to begin with, it will start to bind at the top or rub at the strike side. We’ve replaced enough wood entry doors in Davie that were installed with no clearance for seasonal expansion to know this is a real problem. If you want wood, choose a species like mahogany or Spanish cedar that handles moisture better than oak or maple, and be prepared to maintain the finish.
Sliding and Patio Doors
Sliding glass doors are the workhorse of Davie homes, opening onto pools, patios, and lanais. The most important decision here is the track and roller system. Cheap aluminum rollers wear flat and the door starts grinding. Quality stainless steel rollers with sealed bearings last decades and keep the door operating with two fingers. We also see many Davie homeowners upgrading from traditional sliding doors to multi-slide or pocketing sliding doors, which open entire walls to the outside. That’s a bigger investment, often $8,000 to $20,000 depending on width and configuration, and the structural header work requires a licensed installer. This is not a DIY project, and it’s not one to trust to the lowest bid.
What Windows Cost in Davie
The honest answer is that window costs vary widely based on size, frame material, glass package, impact rating, and installation complexity. But here are the ranges we quote most often in Davie, and they’ll give you a realistic baseline.
- Standard single-hung vinyl window, impact-rated: $600 to $900 per window installed
- Single-hung aluminum window, impact-rated: $700 to $1,000 per window installed
- Sliding window, impact-rated: $800 to $1,300 per window installed
- Picture window, impact-rated: $900 to $1,500 per window installed
- Fiberglass window, impact-rated: $1,100 to $2,000 per window installed
- Casement window, impact-rated: $1,000 to $1,800 per window installed
A few notes on these numbers. First, sizes matter more than most homeowners expect. A 3-foot-by-5-foot window prices differently than a 6-foot-by-5-foot window for more than just the extra glass: it may require additional structural reinforcement, and larger impact units need heavier laminated glass. Second, these are mid-range estimates for direct replacements where the existing opening is sound. If the rough opening has rot, water damage, or termite issues, expect additional carpentry charges, typically $150 to $500 per opening depending on severity.
The variable that surprises Davie homeowners most is the difference between “new construction” windows and “replacement” windows. If your existing frames are solid and square, a replacement window can be installed into them, saving the cost and disruption of tearing out to the studs. If the frames are compromised, a full frame replacement is necessary. In our experience, about 60% of Davie homes built before 2000 need at least some full frame replacements when they do a whole-house window project.
What Doors Cost in Davie
Exterior door pricing in Davie follows the same pattern as windows, driven primarily by material, size, and impact requirements.
- Basic fiberglass entry door, impact-rated: $1,800 to $3,500 installed
- Steel entry door, impact-rated: $1,500 to $3,000 installed
- Wood entry door, custom, impact-rated: $3,500 to $8,000 installed
- French doors, impact-rated, pair: $4,000 to $9,000 installed
- Standard sliding glass door, impact-rated: $2,500 to $5,000 installed
- Multi-slide or pocketing door, impact-rated: $8,000 to $20,000 installed
These numbers assume a straightforward replacement of an existing opening. When the scope changes, so does the price. Changing a single door to a double door, widening an opening for a larger door, or adding a sidelight all involve structural work, stucco repair, and often a new header, any of which can add $1,000 to $4,000 or more to the project. In Davie, where many homes were built in the 1970s and 1980s with older framing techniques, we frequently encounter non-standard rough opening sizes that make off-the-shelf doors impossible. Custom sizing is part of the job, and it should be reflected in the quote, not discovered after the old door is out.
Why Installation Quality Determines Everything
Here’s the part of the guide that matters most. A perfectly manufactured window, installed out of square or without proper flashing, will fail. The glass may stay intact, but the seals will work loose, the frame will rack, and water will find its way into the wall cavity. We’ve been called to Davie homes where new windows were leaking within eighteen months, and the cause was almost always installation error, not a product defect.
What separates a proper installation from a problematic one comes down to a few specific practices:
- Measuring every opening twice. This sounds obvious, but different installers treat it differently. We measure every opening on two visits: once at the quote and once before ordering. Rough openings in Davie homes are rarely perfectly square, and old framing shifts over time. The difference between a rushed measurement and a careful one is a window that fits versus a window that gets shimmed excessively and still looks wrong.
- Flashing and sealing at the bottom, not just the top. The most common water intrusion point in Davie is the sill pan. Windows need a properly sloped, sealed sill pan before the unit goes in. If water gets behind the frame at the bottom, it sits in the wall and eventually rots the framing.
- Setting the window level and square before fastening. Get this wrong and the sashes bind, the glass stresses, and the entire unit works against itself.
- Registering both warranty layers before leaving the driveway. Most window and door manufacturers offer two warranty layers: one on the glass and frame, one on the installation or the insulating glass unit. Many installers never register them. We do, and we produce the paperwork at the end of the job, with durations stated in writing. That’s The Keystone Standard, and it’s part of every installation performed in Davie.
The reason to pay for quality installation in Davie is simple: the labor is a fraction of the total project cost, but labor errors account for most of the failures we see. A window that costs $900 installed is often $400 in product and $500 in labor. Skimp on the labor and you’re risking the other $400 for no good reason.
Energy Efficiency and Your Electric Bill
Davie homeowners run air conditioning roughly ten months out of the year. Windows and doors are the weakest points in the thermal envelope of most homes, which means the efficiency choices you make directly affect what you pay Florida Power & Light every month.
The three numbers that matter on an energy label:
- U-Factor: measures heat transfer through the window. Lower is better. In Davie, look for a U-factor of 0.30 or lower. This is the most important number for cooling-dominated climates.
- Solar Heat Gain Coefficient (SHGC): measures how much solar radiation enters through the glass. Lower means less heat coming in. For Davie, aim for 0.25 or lower.
- Visible Transmittance (VT): measures how much natural light gets through. Higher means brighter rooms. Ideally, find windows with low U-Factor and low SHGC scores but a VT of 0.40 or above.
Two glass technologies dominate the efficient window market in Davie. Low-E coatings are microscopically thin metallic layers applied to the glass that reflect infrared heat while allowing visible light through. Modern Low-E coatings, sometimes called Low-E3 or triple-layer, block most of the solar heat gain that drives up cooling costs. Argon or krypton gas fills between the panes provide additional insulation by reducing conduction and convection. In South Florida’s climate, the combination of Low-E and argon fill typically reduces solar heat gain by 40 to 60 percent compared to clear glass, which translates directly to lower AC demand.
A couple of honest caveats. First, energy savings depend on the overall condition of your home. If your attic insulation is inadequate or your ducts leak, new windows won’t do as much. Second, impact-rated laminated glass, which is required in Davie, is slightly less efficient than non-impact glass at the same low-E rating because the lamination layer holds some heat. The right comparison is not between impact and non-impact glass; it’s between impact glass with a quality Low-E coating and impact glass without one. That difference is measurable on your electric bill, and it’s one of the reasons we always recommend upgrading the glass package even when you’re replacing impact windows.
Maintenance That Extends the Life of Your Investment
Windows and doors in Davie need attention. The homes here face a combination of intense sun, heavy seasonal rain, and humidity that would destroy unmaintained units in other climates within a decade. With basic care, quality windows and doors can last 25 to 40 years. Without it, you’ll be replacing them in half that time.
- Inspect and clean the tracks twice a year. Sliding windows and doors in Davie collect sand, pollen, and debris. When grit accumulates in the track, the rollers grind and the frame scratches. Rinse the tracks, wipe them dry, and apply a silicone-based lubricant to the rollers.
- Check the weatherstripping every fall. The rubber and foam seals around windows and doors break down in heat and sunlight. When the weatherstripping gets brittle or compressed, air leaks appear and your AC works harder. Replacing weatherstripping is inexpensive; ignoring it is not.
- Clear the weep holes. Every window and sliding door frame has small drain holes at the bottom that let condensation and rain escape. These holes clog with dirt and insect debris. A clogged weep hole means water pools in the track and eventually finds its way into the frame or the house. Use a thin wire or compressed air to clear them when you see standing water after a rain.
- Inspect the caulk and sealant annually. The caulk line around windows and doors is your first defense against water intrusion. In Davie’s hot sun, exterior caulk dries and cracks within a few years. Run a bead of quality exterior silicone caulk where you see gaps. On the interior, check for any signs of water staining around the frame, which signals a bigger problem.
- Wash the glass correctly. This sounds trivial, but the wrong technique shortens the life of Low-E coatings. Use a mild soap and a soft cloth or microfiber; never ammonia-based cleaners, which can degrade coatings over time. Avoid pressure washing windows and doors, because the blast can force water past the seals and damage weatherstripping.
Once a year, it’s worth doing a full walkaround of your house in Davie and actually looking at each window and door: how it opens, how it closes, how it feels. A window that’s becoming harder to open or a door that’s starting to stick in August is telling you something. Catching those signs early often means a $50 adjustment instead of a $500 repair. If you’d rather not do this yourself, we offer a maintenance check that covers the basics: track cleaning, roller adjustment, weatherstripping inspection, and lubricating hardware. We’ll be there when we say, uniformed and prepared, and we’ll tell you honestly what needs attention and what doesn’t.
Common Mistakes to Avoid
- Choosing the cheapest bid without comparing scope. Window bids are not apples to apples. One Davie installer may quote a vinyl window with a basic package; another quotes the same brand with impact glass and Low-E. If the price seems too good, ask what’s actually included: glass type, impact rating, installation method, warranty registration. The lowest bid often omits essentials that show up as added charges later.
- Skipping the permit. Some homeowners in Davie are tempted to skip the permit and inspection to save a few hundred dollars. This is a mistake on several levels: it’s a code violation, it can invalidate your insurance coverage, and it creates problems when you sell the home. Permitted, inspected work proves the installation was done correctly.
- Installing non-impact glass on the ground floor. Davie’s High Velocity Hurricane Zone requires impact protection. Installing non-impact windows without shutters to meet code is illegal and dangerous. We’ve seen homeowners buy cheap windows from a big-box store and discover at inspection that they don’t meet code, which means the whole project starts over.
- Ignoring the frame condition. Replacing the glass while leaving a rotted or out-of-square frame is like putting new tires on a bent wheel. In Davie’s humid climate, frame damage caused by water intrusion or termites must be addressed before the new unit goes in, or the new window inherits the old problem.
- Choosing a door based on looks alone. A beautiful front door that isn’t properly sealed, flashed, or fitted for Davie’s humidity will bind in summer and leak in hurricane season. The door needs to function as part of the building envelope, not just as an entry point.
- Not verifying warranty registration. Many window and door warranties are valid only if registered by the installer or homeowner within a specific period, often 90 days. Unregistered warranties can be voided by the manufacturer. We register both warranty layers on every job and provide the paperwork in writing before we leave, because a warranty that isn’t in writing isn’t a warranty you can rely on.
When to Call a Professional
Some window and door issues are simple enough to handle with a screwdriver and some lubricant. Others require a professional who knows Davie’s code requirements and has the equipment to do the job safely. Call a professional when you see water staining around frames, fog between the panes (a failed seal), cracked or broken impact glass, doors that no longer close or lock properly, or visible gaps where the frame has pulled away from the wall. Impact glass replacement is not a DIY project, the units are heavy, and the lamination layer makes them difficult to cut safely. Framing repair, opening resizing, and any structural work should always go through a licensed installer. TruePane Windows & Doors offers free estimates in Davie, call (863) 208-5172 to schedule one.
Frequently Asked Questions
Window replacement in Davie typically costs $600 to $1,400 per window installed for impact-rated units, depending on size, frame material, and glass package. The total for a whole-house project on a 2,000-square-foot home is usually $12,000 to $28,000. Call (863) 208-5172 for an exact quote, estimates are free.
Yes, if you’re replacing windows in Davie, the new units must meet the Florida Building Code’s High Velocity Hurricane Zone requirements for impact resistance, either through impact-rated laminated glass or an approved shutter system. The specific rating depends on your home’s height and location relative to grade. A licensed installer can confirm what your openings require.
The best window for Davie is one that combines impact-rated glass with a quality Low-E coating and is installed square and sealed correctly. PGT, CGI, and Simonton all make reliable impact windows that perform well in South Florida. The installation matters more than the label, which is why we provide side-by-side manufacturer quotes on paper and register both warranty layers in writing.
Quality impact windows and doors in Davie last 25 to 40 years with proper maintenance, while budget units may need replacement within 10 to 15 years. The biggest killers of window and door life in this climate are failed seals, water intrusion, and frame corrosion, all of which are accelerated by installation errors and neglected maintenance.
Yes, in most Davie homes, new windows with Low-E coating and argon gas fill reduce solar heat gain by 40 to 60 percent compared to older clear glass, which directly lowers air conditioning load. The exact savings depend on your home’s insulation, duct condition, and window count. We can walk you through realistic expectations for your specific house during the free estimate.
Doors in Davie stick during summer because wood and some frame materials absorb moisture from the humid air and swell, making the door too tight for the frame. The fix is usually a clearance adjustment or, in severe cases, a door replacement with a material like fiberglass that doesn’t warp. If your door binds in July, call (863) 208-5172 and we’ll send a background-checked technician to assess it.
The Bottom Line
Windows and doors in Davie have to do more than look good. They have to stand up to hurricane-force wind, year-round humidity, and intense sun, all while keeping your utility costs manageable. The right choice comes down to impact-rated glass that meets Florida code, frame materials that hold up in South Florida’s climate, and installation performed by a company that measures carefully, seals properly, and stands behind the work in writing. At TruePane Windows & Doors, we’ve been serving Davie, and we’re not going anywhere. Call (863) 208-5172 for a free estimate. You’ll get a square deal, a straight answer, and work that’s done right.
Written by the team at TruePane Windows & Doors.
Six Reasons Homeowners Choose TruePane Windows & Doors
Impact systems engineered to design pressures up to +/-100, matched to your wind zone - your openings hold when the storm arrives.
Low-E insulated impact glass from our manufacturer lines commonly cuts monthly cooling bills 20-30%.
Laminated impact glass shuts out up to 40% of outside noise - traffic, neighbors, weather.
Monitoring services run $30-90 a month. Laminated impact glass resists forced entry around the clock, with no subscription.
Florida homeowners average around 25% savings on the windstorm portion of their policy after protecting every opening - some homes qualify for more.
A full impact package upgrades curb appeal, buyer confidence and appraised value in one project.



Before
After
Before
After
Before
After