CGI Door Installation Nationwide | TruePane Windows & Doors

CGI Door Installation: The Davie Owner’s Guide

CGI door installation and part replacement in Davie typically runs $290 to $640 installed, depending on the part and your door’s series. We keep common CGI hardware on our trucks and can usually complete the swap in one visit. Most homeowners discover the problem the hard way: a door that suddenly drags, a latch that will not catch, or a hinge that groans like it has been holding that door since the Reagan administration.

Call (863) 208-5172

You are not imagining it. Davie’s heat and humidity are hard on door hardware. Salt air drifts in from the coast, afternoon thunderstorms push moisture into every seam, and the sun beats on western-facing doors until the finish gives up. Parts that would last twenty years in Ohio fail in eight here. When a CGI door starts binding or sagging, the part is usually telling you it is done.

Which CGI Models This Applies To

CGI builds doors across several product lines, and the hardware is not always interchangeable between them. The Sentinel line, the Estate Collection, and the older Classic series all use different hinge profiles and threshold heights. If you have a CGI impact door, the bottom sweep and weatherstripping are thicker than what you will find on a standard door, and using the wrong part voids the water rating. That is the gotcha we see most often: a homeowner buys what looks like the right hinge or roller online, installs it, and the door still binds because the geometry is off by a few millimeters.

Your door has a label. Check the hinge edge near the bottom, or the top of the door panel itself. The label lists the series, the size, and the manufacturing date. Bring us that information when you call, or read it to the technician when we arrive, and we will bring the right part the first time. For CGI specifically, we recommend OEM parts for anything structural: hinges, threshold caps, and strike plates engineered for impact-rated doors. For hardware like rollers and sweeps, quality aftermarket equivalents from reliable suppliers hold up just as well and often cost less. The important thing is that the part is matched to your series, not just your door size.

We are an independent service provider and not affiliated with CGI. We install and service their doors because they are built well for South Florida, but our warranty and workmanship standard are our own. If it is not right in the wall, it is not done.

Signs Your CGI Door Installation Is Failing

• The door drags or scrapes across the threshold. This almost always means the hinge screws have pulled loose from the jamb or the hinges themselves have worn to the point where the door panel is sitting low. Left alone, it will gouge the threshold and wreck the weatherstripping, and then you are paying for both instead of one.
• The latch misses the strike plate or only catches halfway. A settling slab or worn hinge can throw the geometry off enough that the bolt does not seat. This is a security issue as much as a nuisance, and on an impact-rated door in Davie, you do not want a latch that is only half-engaged when a storm rolls through.
• The door sticks hard in summer and swings free in winter. That is the frame swelling with humidity, usually because the door was not sealed properly when it was installed. The fix is often a combination of hinge adjustment and re-sealing the frame, not planing the door down. Plane it, and you just removed the material that was protecting you from the next heavy rain.
• The sweep at the bottom has torn or flattened. On a CGI impact door, that sweep is your water and wind barrier. Once it goes, you will feel the draft and see daylight under the door. Debris from Davie’s summer storms will find its way in, and so will the water.
• The hinges creak loudly or the screws will not stay tight. Loud creaking is the hinge telling you the knuckle is worn out. Screws that spin without tightening mean the wood behind the hinge is stripped. That is a repair we handle regularly, and it usually does not require replacing the whole door, but it does require removing the door panel and doing the work properly.

Replacement Cost & What’s Included

Here is what CGI door installation and part replacement typically costs in Davie, parts and labor included:

The range depends on your door’s series, whether the part is OEM CGI or an aftermarket equivalent we trust, and the condition of the surrounding frame. If the frame is solid, the job is straightforward and falls at the lower end. If water damage or past repairs have compromised the jambs, the labor increases because we fix the framing before we touch the door. We quote line-item prices on paper before we start, and the number on that sheet is the number on your bill. Our work carries the Done Right Promise: if it is not right, we make it right, no paperwork and no arguing. That includes the warranty registration on both layers handled before our truck leaves your driveway.

DIY or Call Us?

Some things you can safely check and even fix yourself with basic tools: tightening a loose hinge screw, cleaning out a dirty track, replacing a torn sweep that slides into a channel at the bottom of the door. Those are maintenance tasks, and a careful owner with a screwdriver can handle them.

What goes wrong in DIY territory is when the door panel has shifted, the hinges are worn, or the frame itself is swelling. Removing a heavy door panel without the right support is how people get hurt and how frames get gouged. If you are dealing with a CGI impact door, that panel can weigh over 150 pounds. That is not a one-person job on a Saturday afternoon, and it is not a part failure you want to improvise around. If the door is binding or the latch will not seat, call us at (863) 208-5172. We will send someone who has done this work in Davie for years, and we will give you a straight answer before we touch anything.

FAQs