Free in-home measure and quote - PGT, CGI and CWS impact lines compared on your actual openings, style by style
Sliding glass doors
Impact garage doorsPGTCGI
Before
After
Before
After
Before
AfterCGI Window Installation in Davie: What to Know First
CGI window installation in Davie typically runs $850 to $2,400 per opening depending on the series, size, and whether you’re replacing a failed unit or doing a full-frame swap. We are an independent CGI service provider, not a manufacturer affiliate, and most single-opening jobs are completed in one visit. If the window is out of square, has a fogged seal, or the frame has moved since the original install, the price shifts accordingly. This page is written for CGI owners in Davie who want the job measured twice, quoted on paper, and installed so it holds up through the next hurricane season. Call (863) 208-5172 and a live person picks up, day or night.
How CGI Products Fail – and How We Fix Them
- Sash balancers on Estate Collection single and double hungs. Davie’s humidity works its way into the balancer channel over ten to fifteen years, and the nylon carrier strips wear thin. The window still opens, but it won’t stay up without a prop. We replace balancers in pairs, re-tension to the sash weight, and the window holds position like it did the day it left the factory floor.
- Roller drag on Estate and Sentinel sliding windows. What starts as a stiff slide becomes a two-hand shove within a season or two. It’s rarely the track; it’s the roller housings picking up grit and corrosion from Davie’s rainy summers and the limestone dust that blows off the Everglades. We swap in rollers with sealed stainless bearings rather than the open nylon ones some aftermarket suppliers sell.
- Fogged insulated glass units in the Estate line. The desiccant strip inside the spacer loses its drying capacity around the twelve-to-fifteen-year mark in South Florida’s heat and humidity. Once moisture appears between the panes, the seal has failed and no amount of caulk will fix it. We measure the daylight opening to the sixteenth of an inch and order the IGU to spec, keeping the original frame and trim intact.
- Header sag above wide fixed and picture windows on older Davie ranch homes. We see this on houses built in the 1970s and 1980s along Southwest 61st Avenue and around the Pine Island Ridge area. The header was undersized for the span, the frame deflects, and the glass binds in the corners. We shim and re-square the frame before setting the new unit, and if the deflection is bad enough, we will tell you to have a structural engineer look at it before we touch the window. A new window will not fix a moving header.
- Awning and casement operator arms on CGI’s Estate series. The arm bends or the gear teeth strip when the window is cranked against a swollen seal or warped sash. We replace the operator with a heavier-duty unit and correct the binding condition first. Replacing the operator alone is a three-hundred-dollar repeat call waiting to happen.
Our CGI Window Installation Process
- 1
Call and schedule. A live person answers. We ask the window count, the CGI series if you know it, and what the window is doing that it shouldn’t. Dale Kessler grew up off Orange Drive near the old Davie Arena and has measured windows in this town for twenty-six years. He still looks at every job before the crew shows up.
- 2
Measurement and diagnosis. Every opening is measured twice, corners checked for square, and the existing flashing inspected. If the failure is a seal, we check whether it’s an IGU swap or a full-frame situation. We write down what we find.
- 3
Parts decision. We use CGI OEM glass and hardware when the job calls for it, and we will tell you when a quality aftermarket roller or balancer performs better and costs less. We quote both on paper side by side. As Dale puts it, “If it is not right on paper, it will not be right in the wall.”
- 4
Installation. The old unit comes out, the opening is prepped, new flashing goes in where needed, and the window is set plumb, square, and level. We seal to the manufacturer’s spec so the warranty stays intact.
- 5
Test and cleanup. Every sash is cycled, locked, and checked for air leaks. We clean the glass, haul the old unit away, and walk you through the work. Both warranty layers are registered in writing before our truck leaves your driveway.
What CGI Window Installation Costs in Davie
| Job Type | Typical Range in Davie |
|---|---|
| Single-hung sash balancer replacement (per window) | $180 to $320 |
| Sliding window roller replacement (per panel) | $160 to $280 |
| Insulated glass unit replacement (per window) | $450 to $900 |
| Casement or awning operator replacement | $210 to $380 |
| Full-frame CGI window install (standard size) | $850 to $1,400 |
| Full-frame install, large fixed or picture window | $1,200 to $2,400 |
Full-frame installs cost more than insert replacements because the old frame, trim, and flashing all come out and go back in correctly. A two-story elevation or a window with extensive stucco repair around the opening will push the number toward the top of the range. We price the job up front and the number on the quote is the number on the bill. Call (863) 208-5172 for a free written estimate on your CGI window installation in Davie.
Why Davie Homeowners Call TruePane Windows & Doors for CGI Work
We are a second-generation glazier’s company, founded by Dale Kessler in 2008 and backed by more than forty-two years of community service through the family trade. Every CGI window installation is covered by the Done Right Promise: if it is not done right, we make it right, no paperwork fights and no arguing. Our technicians are background-checked and uniformed, and they work in your home the way they would work in their own mother’s. We are also an authorized installer for more than a dozen other manufacturer lines including, and PGT, so if the right answer for your home is not another CGI window, we will tell you that on the quote, side by side, and let the numbers speak.
FAQs
No, when the work is done correctly by an independent CGI service provider using manufacturer-spec materials and methods. We install to CGI’s published specifications and register both warranty layers in writing. What voids warranties is a sloppy install, not an independent contractor who follows the spec.
In most cases, yes. CGI’s Estate and Sentinel lines are still in production in current iterations, and for discontinued finishes we can order an IGU or replacement sash that matches within a tight tolerance. We will show you the match on paper before we order anything.
If the frame is solid and square and the glass is the only failure, an insulated glass unit replacement costs roughly half what a full-frame replacement costs and keeps your original trim intact. If the frame is warped, the header is sagging, or the window is twenty-plus years old and the seals are failing one after another, replacement is the better money. We will quote both and let you decide.
Most single-opening jobs are done in one visit, and our schedule typically allows us to be at your home within a few business days of the quote. Custom-sized IGUs may add a week or two for fabrication. When we schedule, we show up: “We’ll be there when we say” is not a slogan, it is how we run the board.
Yes, when the scope requires it. A like-for-like glass or hardware replacement rarely needs a permit, but a full-frame or structural change does, and we handle the permit, the inspection, and the paperwork before we consider the job finished. You will never be the one chasing the building department.
If you have a CGI window that is binding, fogging, or just not right and you want a straight answer from someone who has worked Davie for twenty-six years, call TruePane Windows & Doors at (863) 208-5172. We will measure, quote it on paper, and stand behind the work. A square deal, done right.
Written by Dale Kessler, Owner, TruePane Windows & Doors at TruePane Windows & Doors, serving Davie and nearby areas.
Six Reasons Homeowners Choose TruePane Windows & Doors
Impact systems engineered to design pressures up to +/-100, matched to your wind zone - your openings hold when the storm arrives.
Low-E insulated impact glass from our manufacturer lines commonly cuts monthly cooling bills 20-30%.
Laminated impact glass shuts out up to 40% of outside noise - traffic, neighbors, weather.
Monitoring services run $30-90 a month. Laminated impact glass resists forced entry around the clock, with no subscription.
Florida homeowners average around 25% savings on the windstorm portion of their policy after protecting every opening - some homes qualify for more.
A full impact package upgrades curb appeal, buyer confidence and appraised value in one project.