PGT Door Installation Nationwide | TruePane Windows & Doors

PGT Door Installation in Davie: What to Know First

PGT door installation in Davie typically runs $2,800 to $7,500 for a standard single entry door, and $5,500 to $14,000 for double French or bifold setups, depending on the product series and what the existing opening needs. We’re an independent PGT service provider, which means we install and service PGT doors without being beholden to any manufacturer’s sales targets. Most PGT door installs take one full day on site, and we register both warranty layers before our truck leaves your driveway.

Call (863) 208-5172

This page is for Davie homeowners who already own PGT doors, or are about to, and want to know what a correct installation actually looks like. If you’ve had a door bind in summer, leak at the threshold, or fail its first real storm, you already know why the installer matters more than the sticker on the glass. Call (863) 208-5172 and you’ll get a live person, not a voicemail tree, every hour of the day.

Key Takeaways

• We install PGT doors correctly the first time – squared, sealed, and registered per manufacturer spec, with a Done Right Promise behind the work.
• Davie’s climate punishes shortcuts – high humidity, salt air from the coast, and hurricane-driven rain demand installation practices that generic door crews skip.
• Both warranty layers get registered in writing before we leave – if the form isn’t filed, the warranty isn’t real, and we don’t let that happen.
• Upfront pricing in writing – no surprise line items after the job starts, and no second appointment left hanging.

How PGT Doors Fail in Davie – and How We Fix Them

PGT builds a strong product, but every door line has its known pressure points. Here’s what we see on Davie doorways week after week, and what we do about it when we’re called in.

• Sagging hinges on PGT WinGuard and Estate Collection entry doors. These are heavy doors – impact-rated, often with laminated glass and reinforced frames. When the hinge screws strip the jamb or the slab settles, the door drops, the deadbolt stops lining up, and the weatherstripping tears along the top. We re-shim the jamb, replace worn hinges with a heavier gauge, and reset the slab so the reveal is even on all three sides. A level tells no lies.
• Threshold rot on ClassicVue and standard PGT swing doors in Davie’s wet-dry-wet cycle. The original threshold gets caulked against the concrete slab, but Florida’s afternoon downpours and eight months of humidity work that seal until water wicks underneath. You’ll see dark staining at the bottom corners of the jamb, or a soft spot in the subfloor just inside the door. We pull the door, inspect the substrate, replace rotted sections, and set the new threshold in a continuous bed of polyurethane sealant – not a bead of latex caulk that fails in a year.
• Fogged or failed sealed units on PGT sliding patio doors. A fogged pane means the insulated glass unit lost its seal, and that’s a replacement, not a wipe-down. On PGT sliders, we see seal failure most often on west-facing elevations in Davie where the afternoon sun beats through a screen enclosure. We order the correct OEM-spec IGU, replace it, and verify the frame drain holes are clear so the track doesn’t hold water against the new glass.
• Roller and track failures on older PGT Custom Windows & Doors sliders. The rollers wear, the track collects sand and dirt from Davie yards, and suddenly a door that used to glide one-handed needs two hands and a hip-check. We don’t just swap rollers – we clean and inspect the track, check for any bow or deflection in the header, and confirm the door still locks square against the jamb. If the track has worn through its coating, you’ll hear it. We see it.
• French door warping on double units exposed to full sun in western Davie neighborhoods. Two slabs in one opening means two different rates of expansion. One door stays shaded, the other bakes. The result is a center gap that shifts with the weather, and a lock that works in February and fights you in August. We install multi-point hardware where possible, adjust the astragal so the active and passive slabs meet properly, and make sure each door’s hinges carry the weight they’re rated for – not the aesthetic version a previous installer picked because it looked right.

Our PGT Door Installation Process

When we install a PGT door in Davie, the job follows a sequence Dale Kessler has refined over twenty-six years in Broward County. No skipped steps, no “good enough” measurements.

1. 1
   The call. You reach a live person. We ask what you’re seeing, what the door is doing (or not doing), and we schedule a site visit at a time that works for you.
2. 2
   The measure and inspection. We measure every opening twice – width at top, middle, and bottom, height on both jambs, and diagonal both ways. If the rough opening is out of square by more than a fraction, we note it and plan for shims and furring before any door gets ordered.
3. 3
   The parts decision. We quote OEM PGT components where the warranty or product integrity calls for them, and we discuss quality aftermarket options where they genuinely perform as well or better. You see the options side by side on paper, with prices, before anything is ordered.
4. 4
   Installation day. We show up in uniform, drop cloths down, and remove the old door carefully because the jamb tells us what the last guy did wrong. We set the new door plumb and square, shim behind every hinge point, and level the threshold before anchoring.
5. 5
   Sealing and testing. We run a continuous seal at every flashing point, test the door through a full open-close cycle at least six times, check the deadbolt alignment, and spray-test the threshold where water tends to enter. If it’s a hurricane-rated unit, we confirm all hardware is installed per PGT’s current HRS requirements.
6. 6
   Paperwork and cleanup. Both warranty layers get registered in writing before we leave your driveway. You get a copy, we keep a copy, and the manufacturer gets a copy. Then the old door, packaging, and debris leave with us. Your driveway looks like we were never there – except for a door that finally closes right.

What PGT Door Installation Costs in Davie

These are honest ranges based on what we see across Davie installations – not teaser prices that grow once the job starts. The big variables are the rough opening condition, the glass and frame options on the PGT series you choose, and whether the existing structure needs shoring up before the new door goes in. Call (863) 208-5172 and we’ll walk through your specific project and give you a written line-item quote. The estimate is free, and the number you get is the number you pay.

Why Davie Homeowners Call TruePane Windows & Doors for PGT Work

We’ve been serving Broward County for over forty-two years through Dale Kessler’s family trade, and the company he founded in 2008 carries the same rule he learned from his father: if the pane is not true, the job is not done. That’s the Keystone Standard, and it means both manufacturer warranty layers get registered in writing before we leave your driveway, with durations stated, so you never have to wonder if your PGT warranty is actually active.

If something isn’t right, the Done Right Promise is simple: we make it right. No paperwork fights, no arguing, no fine print that covers neither. Our technicians are background-checked and uniformed, and they measure every opening twice. We work on PGT, Andersen, Pella, and CGI, so when a door has a problem, we can tell you honestly what’s repairable and what’s finished – without steering you toward a replacement because that’s the only line we carry.

FAQs